Jump to content
Sturgeon's House
  1. delete013

    delete013

  2. Lord_James

    Lord_James

  • Similar Content

    • By Monochromelody
      IDF had kept about 100 Tiran-6/T-62s since 1973, and remain service until 1990s. 
       
      I wonder if there's any modification on Tiran-6, like changing the powerpack into 8V71T+XTG-411, adapting steering wheel. 
       
      I also heard that British ROF had produce a batch of 115mm barrel for IDF, while MECAR or NEXTER produced high-performance APFSDS for 115mm gun. Did IDF really use these barrels for original barrel replacement? 
       
      And about protection, did IDF put Blazer ERA on Tiran-6? Or they use more advanced APS like Trophy? 
       
      Thank you. 
    • By Sturgeon
      The LORD was with the men of Deseret. They took possession of the hill country, but they were unable to drive the people from the plains, because they had chariots of steel.
      —The Book of Latter Day Saints, Ch 8, vs. 3:10, circa 25th Century CE
       
      BULLETIN: ALL INDUSTRIAL-MECHANICAL CONCERNS
       
      SOLICITATION FOR ALL-TERRAIN BATTLE TANK
       
      The Provisional Government of the Lone Free State of Texas and The Great Plains issues the following solicitation for a new All-Terrain Battle Tank. The vehicle will be the main line ground combat asset of the Lone Free State Rangers, and the Texas Free State Patrol, and will replace the ageing G-12 Scout Truck, and fill the role of the cancelled G-42 Scout Truck. The All-Terrain Battle Tank (ATBT) will be required to counter the new Californian and Cascadian vehicles and weapons which our intelligence indicates are being used in the western coast of the continent. Please see the attached sheet for a full list of solicitation requirements.
       

       
      Submissions will be accepted in USC only.
       
       
      Supplementary Out of Canon Information:
       
       
      I.     Technology available:
      a.      Armor:
      The following armor materials are in full production and available for use. Use of a non-standard armor material requires permission from a judge.
      Structural materials:
                                                                    i.     RHA/CHA
      Basic steel armor, 360 BHN. The reference for all weapon penetration figures, good impact properties, fully weldable. Available in thicknesses up to 4 inches (RHA) 8 inches (CHA). 
      Density- 0.28 lb/in^3.
                                                                   ii.     Aluminum 5083
      More expensive to work with than RHA per weight, middling impact properties, low thermal limits. Excellent stiffness.
       Fully weldable. Available in thicknesses up to 4 inches.
      Mass efficiency vs RHA of 1 vs CE, 0.9 vs KE.
      Thickness efficiency vs RHA of 0.33 vs CE, 0.3 vs KE.
      Density- 0.1 lb/in^3 (approx. 1/3 of steel).
      For structural integrity, the following guidelines are recommended:
      For heavy vehicles (30-40 tons), not less than 1 in RHA/1.75 in Aluminum base structure
      For medium-light vehicles (<25 tons), not less than 0.5 in RHA/1 in Aluminum base structure
      Intermediate values for intermediate vehicles may be chosen as seen fit.
      Non-structural passive materials:
                                                                  iii.     HHA
      Steel, approximately 500 BHN through-hardened. Approximately 1.5x as effective as RHA against KE and HEAT on a per-weight basis. Not weldable, middling shock properties. Available in thicknesses up to 1 inch.
      Density- 0.28 lb/in^3
                                                                  iv.     Fuel
      Mass efficiency vs RHA of 1.3 vs CE, 1 vs KE.
      Thickness efficiency vs RHA of 0.14 vs CE, 0.1 vs KE.
      Density-0.03 lb/in^3.
                                                                v.     Assorted stowage/systems
      Mass efficiency vs RHA- 1 vs CE, 0.8 vs KE.
                                                               vi.     Spaced armor
      Requires a face of at least 1 inch LOS vs CE, and at least 0.75 caliber LOS vs fullbore AP KE.
      Reduces penetration by a factor of 1.1 vs CE or 1.05 vs KE for every 4 inchair gap.
      Spaced armor rules only apply after any standoff surplus to the requirements of a reactive cassette.
      Reactive armor materials:
                                                                  vii.     ERA
      A sandwich of 0.125in/0.125in/0.125in steel-explodium-steel.
      Requires mounting brackets of approximately 10-30% cassette weight.
      Must be spaced at least 2 sandwich thicknesses away from any other armor elements to allow full functionality. 81% coverage (edge effects).
                                                                  viii.     NERA
      A sandwich of 0.25in steel/0.25in rubber/0.25in steel.
      Requires mounting brackets of approximately 10-30% cassette weight.
      Must be spaced at least 1 sandwich thickness away from any other armor elements to allow full functionality. 95% coverage.
      The details of how to calculate armor effectiveness will be detailed in Appendix 1.
      b.      Firepower
                                                                    i.     Bofors 57mm (reference weapon) - 85,000 PSI PMax/70,000 PSI Peak Operating Pressure, high quality steel cases, recoil mechanisms and so on are at an equivalent level to that of the USA in the year 1960.
                                                                   ii.     No APFSDS currently in use, experimental weapons only - Spindle sabots or bourelleted sabots, see for example the Soviet BM-20 100mm APFSDS.
                                                                  iii.     Tungsten is available for tooling but not formable into long rod penetrators. It is available for penetrators up to 6 calibers L:D.
                                                                  iv.     Texan shaped charge technology - 4 CD penetration for high-pressure resistant HEAT, 5 CD for low pressure/ precision formed HEAT.
                                                                   v.     The subsidy-approved GPMG for the Lone Free State of Texas has the same form factor as the M240, but with switchable feed direction.. The standard HMG has the same form factor as the Kord, but with switchable feed direction.
      c.       Mobility
                                                                    i.     Engines tech level:
      1.      MB 838 (830 HP)
      2.      AVDS-1790-5A (908 HP)
      3.      Kharkov 5TD (600 HP)
      4.    Detroit Diesel 8V92 (400 HP)
      5.    Detroit Diesel 6V53 (200 HP)
                                                                   ii.     Power density should be based on the above engines. Dimensions are available online, pay attention to cooling of 1 and 3 (water cooled).
                                                                  iii.     Power output broadly scales with volume, as does weight. Trying to extract more power from the same size may come at the cost of reliability (and in the case of the 5TD, it isn’t all that reliable in the first place).
                                                                  iv.     There is nothing inherently wrong with opposed piston or 2-stroke engines if done right.
      d.      Electronics
                                                                    i.     LRFs- unavailable
                                                                   ii.     Thermals-unavailable
                                                                  iii.     I^2- Gen 2 maximum
                                                                  vi.     Texas cannot mass produce microprocessors or integrated circuits
                                                                 vii.    Really early transistors only (e.g., transistor radio)
                                                                viii.    While it is known states exist with more advanced computer technology, the import of such systems are barred by the east coast states who do not approve of their use by militaristic entities.
       
      Armor calculation appendix.
       
      SHEET 1 Armor defeat calculator 4in-54 1200 yd
       
      SHEET 2 Armor defeat calculator 4in-54 2000 yd
       
      SHEET 3 Armor defeat calculator 6in HEAT
       
      Range calculator
       
    • By SuperComrade
      I was recently looking at the Japanese wikipedia page for the Chi-Ha tank, and it had this section on the name of the tank:

       
       
      I have never heard of such nomenclature, and obviously I don't have access to such documents since I don't live in Japan. There is no reference for this part, so can anyone confirm that they actually did use "MTK" etc.?
    • By pizza654
      Hi as most of you know who are in the gun community a bunch of AR 70/90 kits came into the country and theirs still no barrels or receivers in production. Since I cant find anything I decided that I'm just going to make my own barrel and I've found the measurements from a guy on reddit who lives in Italy. 
       
      https://imgur.com/gallery/WUtxuAP
       
      https://imgur.com/gallery/1ydhDUS
       
      As I was getting the measurements a curiosity ran through my head, how do you mathematically figure out the proper diameter of the gas port hole for the gas block in the barrel?
       
      Much help will be appreciated! 
       
       
×
×
  • Create New...